Kasama sa makina
1. Hydraulic single arm de-coiler with hydraulic feeding trolley
2. 15-axis dual-type precision leveling machine
3. Correction device (including trench tray)
4. Nine-roller servo sizing machine
5. Shearing machine
6. Electronic control system
7. Conveyor
8. Lifting palletizer
9. 4000mm in front of discharge platform
10. Hydraulic station
11. Fan
Overflow ng cut sa haba na linya
Hydraulic single arm de-coiler na may hydraulic feeding trolley
1. structure
Ang makina ay isang single-head cantilever hydraulic expansion at contraction unwinder, na binubuo ng isang pangunahing bahagi ng shaft at isang bahagi ng transmission.
(1) The main shaft part is the core part of the machine. Its four blocks are connected to the sliding sleeve through T-shaped slanting blocks and are simultaneously sleeved on the hollow spindle. The core is connected to the sliding sleeve. The fan blocks expand and contract at the same time. When the fan block shrinks, it is beneficial to roll up, and when the fan block is opened, the steel coil is tightened to complete the unwinding.
(2) The pressure roller is located behind the unwinder. The pressing arm is controlled by the oil cylinder to drive the cantilever to be pressed down and picked up. When feeding, the cantilever pressing roller is pressed to press the steel coil to prevent loosening and facilitate the feeding.(3) The transmission part is located outside the frame. The motor and reducer drive the main shaft of the unwinder through the gear to rotate, and it can also realize unwinding and rewinding.
2. Technical Parameters
(1) Steel coil width: 500mm-1500mm
(2) Steel coil weight: 10T
(3) Cylinder stroke: 600mm
Pagpapatakbo ng motor: 2.2kw
15-axis dual-type na precision leveling machine
1. Leveling rollers: 15
2. Leveling roller diameter: 120mm
3. Leveling roller material 45 # steel
4. Motor power: 22KW
5. The leveling effect is according to the first grade coil, except for scrap or secondary board.
6. Leveling roller material: 45 # steel.
7. After tempering, quenching and grinding, the surface hardness reaches HRC58-62, and the surface finish is Ra1.6mm.
8. The upper row of work rolls are lifted vertically by a motor drive.
9. Roller bearings are used for the work roll bearings, which have a high bearing capacity and a long service life.
Pangunahing sistema ng puwersa: Ang isang motor ay pinaandar sa gitna at hinihimok ng unibersal na joint ng reducer transmission box.
Pit
1. It uses the 2 groups of magic eyes to control the speed buffer between decoiler and slitting machines.
2. Magic eye is controlled by PLC.
3. Function: it is used to eliminate the different speed and make the plates which in wrong rail to back the right way. At first, it is used the oil cylinder to lifting the supporting and transition plates to make the head pass. When working, the transition and supporting plates lift down, the steel plates will be stored in the pit.
Correction device with Nine-roller servo sizing machine
Device sa pagwawasto:
1. Guided by vertical guide rollers. Adjust the distance between the two guide rollers manually.
2. Minimum guide width 500mm
Nine-roller servo sizing machine specifications
1. Feeding rollers: 9
2. Leveling roller diameter:120mm
3. Fixed-length roller diameter: 160mm
4. Roller material 45 # steel
Servo motor: 11kw
Pneumatic Shearing machine
Pneumatic Shearing machine:
Pangunahing binubuo ito ng kaliwa at kanang bracket, connecting rods, upper at lower tool holder, table, driving motors, atbp.
(1) Maximum cutting thickness: 3mm
(2) Shearing width: 1600mm
(3) Motor power: 11KW
Conveyor belt:
Conveyor belt:
1. Belt length :7500mm
2. Width: 1450mm
Motor 2.2kw (kontrol sa dalas)
Pag-aangat ng palletizer
Lifting palletizer (Note: 4000mm lifting position, source of gas)
1. The blanking machine mainly carries out the blanking of the sheet, which is composed of a horizontally moving rack body and a vertical baffle.
2. The horizontal moving frame is manually adjusted according to different board widths, and the vertical baffle is adjusted according to different board lengths.
3. The stacking machine is mainly composed of stacking cylinder walking rollers and motors. Its function is to neatly stack the blanked plates.
Ang pangunahing teknikal na mga parameter
(1) Height of blanking rack: 2100mm
(2) Total length of blanking rack: 4300mm
(3) Total width: 2300mm
Rack na nagdadala ng pagkarga: 10000kg